The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?()A.network 172.26.168.0 area 478B.network 172.26.0.0C.network 172.26.168.128 0.0.0.127D.network 172.2

题目
The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?()

A.network 172.26.168.0 area 478

B.network 172.26.0.0

C.network 172.26.168.128 0.0.0.127

D.network 172.26.168.128 area 478

相似考题

1.Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）A. 172.17.0.0/30B. 172.17.1.0/24C. 172.17.2.0/24D. 172.17.3 .0/25E. 172.17.3.128/25F. 172.17.10.0/24

2.According to the following output, can you tell me which command can redistribute IGRP into EIGRP?()A. Under t he router eigrp mode add redistribute igrp 123 subnetsB. Under the router igrp mode add redistribute eigrp 123C. None, EIGRP and IGRP are automatically redistributed in this instance.D. Under the router eigrp mode add redistribute igrp 123

3.Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）A. Redistribute connected interfaces on router B and router CB. Set the maximum nu mber of equal cost paths to1 in all routersC. When redistributing EIGRP into OSPF, set the external metric type to type E1D. Adjust the default metrics in router B and router C so that the values are different in each routerE. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol

4.Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

更多“The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?() ”相关问题

  • 第1题：

    Refer to the exhibit. Router B is performing bidirectional redistribution between EIGRP an d OSPF.The network 10.100.1.0/24 should not be reachable from the 10.100.9.0/24 network. However, it needs to be reachable from any network within the EIGRP domain. All other networks should be seen in both domains. Which change to router B would accom plish these goals?（）

    A. Under the EIGRP process, insert the distribute - list block_net_1 out ospf 1 command.

    B. Under the OSPF process, insert the distribute - list block_net_1 in serial1/0 command.

    C. Under the EIGRP process, insert the distribute - list block_net_1 in serial1/0 command.

    D. Under the OSPF process, insert the distribute - list block_net_1 out eigrp 1 command.


    参考答案：D

  • 第2题：

    After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? ()

    A. The network has been stable for at least the last 45 minutes

    B. There is a flapping link or interf ace, and router C knows an alternate path to the network

    C. There is a flapping link or interface, and router A does not know an alternate path to the network

    D. EIGRP is not working correctly on router C

    E. There is not enough information to make a determination


    参考答案：A

  • 第3题：

    Refer to the exhibit. A partial routing configuration is shown. Complete the configuration so that only the default - network is redistributed from EIGRP 190 into EIGRP 212. Which ACL statement completes the configuration correctly? （）

    A. access - list 100 permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0 .0

    B. access - list 100 permit ip host 0.0.0.0 any

    C. access - list 100 permit ip any host 0.0.0.0

    D. A default -network cannot be redistributed between routing processes.


    参考答案：C

  • 第4题：

    TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）

    A. TestKing# show eigrp entries

    B. TestKing# show protocols

    C. TestKing# debug eigrp routes

    D. TestKing# show ip route eigrp

    E. TestKing# show route eigrp


    参考答案：D

  • 第5题：

    Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）

    A.Check and change the access lists on router RTA

    B.Configure the auto summary command under router eigrp 1 on router RTA

    C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface

    D.Issue the no ip split horizon command on router RTA

    E.Issue the no ip split horizon eigrp 1 command on router RTA

    F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers


    参考答案：E

  • 第6题：

    TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）

    • A、TestKing# show eigrp entries
    • B、TestKing# show protocols
    • C、TestKing# debug eigrp routes
    • D、TestKing# show ip route eigrp
    • E、TestKing# show route eigrp

    正确答案:D

  • 第7题：

    You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）

    • A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.
    • B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.
    • C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.
    • D、There is no network statement configuration in EIGRP for IPv6.
    • E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.
    • F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive

    正确答案:A,D,E

  • 第8题：

    Which command will display all the EIGRP feasible successor routes known to a router?（）

    • A、Router# show ip eigrp routes *
    • B、Router# show ip eigrp summary
    • C、Router# show ip eigrp topology
    • D、Router# show ip eigrp adjacencies
    • E、Router# show ip eigrp neighbors detail

    正确答案:C

  • 第9题：

    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1

    • A、EIGRP works on F0/0 and S0/0/0 without further configuration
    • B、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE
    • C、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE
    • D、EIGRP for IPv6 needs at least two more configuration commands before it works on R1

    正确答案:D

  • 第10题：

    多选题
    Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）
    A

    Receive - only

    B

    Stub

    C

    Static

    D

    Summary

    E

    Connected

    F

    Dynamic


    正确答案： B,A
    解析： 暂无解析

  • 第11题：

    单选题
    The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?（）
    A

    network 172.26.168.0 area 478

    B

    network 172.26.0.0

    C

    network 172.26.168.128 0.0.0.127

    D

    network 172.26.168.128 area 478


    正确答案： B
    解析： 暂无解析

  • 第12题：

    多选题
    You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）
    A

    EIGRP for IPv6 is directly configured on the interfaces over which it runs.

    B

    EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.

    C

    There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.

    D

    There is no network statement configuration in EIGRP for IPv6.

    E

    When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.

    F

    When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive


    正确答案： A,E
    解析： 暂无解析

  • 第13题：

    After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What information can you determine about this network?()

    A. The network is stable

    B. There is a flapping link or interface, and router C knows an alternate path to the network

    C. There is a flapping link or interf ace, and router C does not know an alternate path to the network

    D. EIGRP is not working correctly on router C

    E. There is not enough information to make a determination


    参考答案：B

  • 第14题：

    Refer to the exhibit. Which statement about dynamic routing protocols for this network is true? ()

    A.No dynamic interior routing protocol can summarize as shown

    B.Unless configured otherwise, EIGRP would automatically summa rize the prefixes as shown in the exhibit

    C.With this IP addressing scheme, EIGRP can be manually configured to summarize prefixes at the specified summarization points

    D.The IP address design lends itself to OSPF Each summarizing router would be an ABR, summarizing to the next area in the address hierarchy


    参考答案：C

  • 第15题：

    Refer to the exhibit. R1 accesses the Internet using E0/0. You have been asked to co nfigure R1 so that a default route is generated to its downstream devices (191.0.0.1 and 192.0.0.1). Which commands would create this configuration? （）

    A.router eigrp 190redistribute static ! ip route 0.0.0.0 0.0.0.0 Null0

    B.ip default - network 2 0.0.0.0

    C.router eigrp 190 redistribute static ! ip route 0.0.0.0 255.255.255.255 Null0

    D.ip default - network 20.20.20.0


    参考答案：A

  • 第16题：

    Router R1 is configured as shown below:router eigrp 100network 10.0.0.0eigrp stubBased on the information shown above, which two types of routes will be advertised?()

    A. Receive - only

    B. Stub

    C. Static

    D. Summary

    E. Connected

    F. Dynamic


    参考答案：D, E

  • 第17题：

    A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）

    A. Router# show ip eigrp adjacency

    B. Router# show ip eigrp topology

    C. Router# show ip eigrp interfaces

    D. Router# show ip eigrp neighbors


    参考答案：D

  • 第18题：

    An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command: 10.8.88.0/25 10.8.89.48/29 10.8.64.96/27 Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）

    • A、10.8.64.0 255.255.224.0
    • B、10.8.64.0 255.255.128.0
    • C、10.8.64.0 255.255.192.0

    正确答案:A

  • 第19题：

    The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?（）

    • A、network 172.26.168.0 area 478
    • B、network 172.26.0.0
    • C、network 172.26.168.128 0.0.0.127
    • D、network 172.26.168.128 area 478

    正确答案:B

  • 第20题：

    A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）

    • A、Router# show ip eigrp adjacency
    • B、Router# show ip eigrp topology
    • C、Router# show ip eigrp interfaces
    • D、Router# show ip eigrp neighbors

    正确答案:D

  • 第21题：

    Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）

    • A、Receive - only
    • B、Stub
    • C、Static
    • D、Summary
    • E、Connected
    • F、Dynamic

    正确答案:D,E

  • 第22题：

    单选题
    TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）
    A

    TestKing# show eigrp entries

    B

    TestKing# show protocols

    C

    TestKing# debug eigrp routes

    D

    TestKing# show ip route eigrp

    E

    TestKing# show route eigrp


    正确答案： D
    解析： 暂无解析

  • 第23题：

    单选题
    In a bridged 1483 network， what configuration command allows the ERX Edge Router to advertise customer networks into the provider’s IGP？ （）
    A

    redistribute direct

    B

    redistribute static

    C

    redistribute connected

    D

    redistribute access-internal


    正确答案： C
    解析： 暂无解析

相关内容