Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example,

题目

Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）

A. Redistribute connected interfaces on router B and router C

B. Set the maximum nu mber of equal cost paths to1 in all routers

C. When redistributing EIGRP into OSPF, set the external metric type to type E1

D. Adjust the default metrics in router B and router C so that the values are different in each router

E. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol

相似考题

1.You have been asked to establish reachability between Router 1‘s and Router 2‘s loopback addresses as shown in the exhibit. Which two steps will accomplish this task?()A. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.2.B. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.1.C. Create a static route on Router 2 to 172.17.25.1 with a next hop of 10.10.10.1.D. Create a static route on Router 1 to 172.17.25.1 with a next hop of 10.10.10.2.

2.Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? ()A. area 0 stub o n routers R4 and R5B. area 5 stub on routers R4 and R5C. area 5 stub no - summary on routers R4 and R5D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5E. area 5 stub no - summary on router R4 and area 5 stub on router R5

3.Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

4.Refer to the exhibit. This shows the NetFlow statistics for a router. You are analyzing the traffic pattern and you are interested in the percentage of packets between 32 and 64 bytes in size and the number of flows in progress. Which of these identifies both numbers correctly?（）A. 69.4%, 4061B. 24.9%, 980C. 69.4%, 35D. 6.94%, 980E. cannot be determined from this output

更多“Refer to the exhibit. Router B and router C are performing mutual redistribution between O ”相关问题

  • 第1题：

    Refer to the exhibit. Router B is performing bidirectional redistribution between EIGRP an d OSPF.The network 10.100.1.0/24 should not be reachable from the 10.100.9.0/24 network. However, it needs to be reachable from any network within the EIGRP domain. All other networks should be seen in both domains. Which change to router B would accom plish these goals?（）

    A. Under the EIGRP process, insert the distribute - list block_net_1 out ospf 1 command.

    B. Under the OSPF process, insert the distribute - list block_net_1 in serial1/0 command.

    C. Under the EIGRP process, insert the distribute - list block_net_1 in serial1/0 command.

    D. Under the OSPF process, insert the distribute - list block_net_1 out eigrp 1 command.


    参考答案：D

  • 第2题：

    You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes.Which two things should you verify to troubleshoot this problem?（）

    A. The border router is using a proper seed metric for OSPF

    B. The border ro uter is using a proper seed metric for EIGRP

    C. The administrative distance is set for OSPF and EIGRP

    D. The missing EIGRP routes are present in the routing table of the border router

    E. The subnet keyword on the border router in the redistribute EIG RP command


    参考答案：D, E

  • 第3题：

    Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?()

    A. Redistribution must be enabled mutually (in both directions) to work correctly.

    B. auto - summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.3 4.0.0, which is already covered by the EIGRP protocol.

    C. Default metrics are not configured under EIGRP.

    D. Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.


    参考答案：C

  • 第4题：

    Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?()

    A. the serial 1/1 address

    B. the serial 2/0 address

    C. a randomly generated internal address

    D. the configured router - id address


    参考答案：D

  • 第5题：

    Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）

    A. both routers R1 and R2

    B. router R1

    C. router R2

    D. none of the routers since they are not configured with static RP


    参考答案：C

  • 第6题：

    Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200?()

    A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5

    B. None of the BGP updates that are received on router R2 will ever be received by router R5

    C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4

    D. All BGP updates that are received on router R2 will be sent directly to router R5


    参考答案：B

  • 第7题：

    Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）

    A.Check and change the access lists on router RTA

    B.Configure the auto summary command under router eigrp 1 on router RTA

    C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface

    D.Issue the no ip split horizon command on router RTA

    E.Issue the no ip split horizon eigrp 1 command on router RTA

    F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers


    参考答案：E

  • 第8题：

    Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?（）

    A.The design will function as intended

    B.Spanning-tree will need to be used.

    C.The router will not accept the addressing scheme.

    D.The connection between switches should be a trunk.

    E.The router interfaces must be encapsulated with the 802.1Q protocol.


    参考答案：C

  • 第9题：

    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

    • A、As numbers must be changed to match on all the routers.
    • B、Loopback interface must be configured so a DR is elected.
    • C、The no auto-summary command is needed on Router A and Router C.
    • D、Router B needs to have two network statements, one for each connected network.

    正确答案:A

  • 第10题：

    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）

    • A、Router1 has specific boot system command that instruct it to load IOS from TFTP server.
    • B、Router1 is acting as a TFTP server for other routers.
    • C、Router1 cannot locate a valid IOS image in flash memory.
    • D、Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
    • E、Cisco routers will first attempt to load a image from TFTP for management purposes.

    正确答案:A,C

  • 第11题：

    单选题
    Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
    A

    Router A is the master virtual router， and Router B is the backup virtual router. When Router A fails， Router B will become the master virtual router. When Router A recovers， Router B will maintain the role of master virtual route

    B

    Router A is the master virtual router， and Router B is the backup virtual router. When Router A fails， Router B will become the master virtual router. When Router A recovers， it will regain the master virtual router role

    C

    Router B is the master virtual router， and Router A is the backup virtual router. When Router B fails， Router A will become the master virtual router. When Router B recovers， Router A will maintain the role of master virtual router.

    D

    Router B is the master virtual router， and Router A is the backup virtual router. When Router B fails， Router A will become the master virtual router. When Router B recovers， it will regain the master virtual router role


    正确答案： A
    解析： 暂无解析

  • 第12题：

    单选题
    Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?（）
    A

    The design will function as intended

    B

    Spanning-tree will need to be used.

    C

    The router will not accept the addressing scheme.

    D

    The connection between switches should be a trunk.

    E

    The router interfaces must be encapsulated with the 802.1Q protocol.


    正确答案： C
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?()

    A. router rip

    B. router eigrp 10

    C. redistribute eigrp 10

    D. redistribute rip

    E. default - metric 10000 100 255 1 1500

    F. default - metric 5


    参考答案：A, C, F

  • 第14题：

    Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?（）

    A. Enter the configuration on router B1.

    B. Enter the configuration on router B4.

    C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.

    D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.

    E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.


    参考答案：A, D

  • 第15题：

    Refer to the exhibit. Routing updates for the 192.168.1.0 network are being received from all three neighbors. Which statement is correct regarding the result of the con figuration shown? ()

    A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.

    B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.

    C. The router will adve rtise the 192.168.1.0 network only to 172.30.1.1.

    D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.

    E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.


    参考答案：B

  • 第16题：

    Refer to the exhibit. What three statements are true about the IS － IS configuration?()

    A.The router is in area 49.0001.0002

    B.The router acts as a Level 1 - 2 router

    C.CLNS routing is enable d for the router

    D.The router has a system ID of 0003.0004

    E.The interfaces have a functional IS - IS configuration

    F.The network service access point selector (NSEL) byte has a value of 0


    参考答案：B, E, F

  • 第17题：

    Refer to the exhibit. Router RT - 1 and router RT - 2 both advertise network 131.25.0.0/16 to routerRT - 3 via internal BGP. What is the reason that router RT - 3 chose router RT - 1 as its best path tonetwork 131.25.0.0/16.（）

    A. It has a better router ID

    B. It advertises a lower autonomous system

    C. It advertises t he best AS - path

    D. It advertises the best local preference

    E. It advertises the best origin code

    F. It advertises the best MED


    参考答案：A

  • 第18题：

    Refer to the exhibit. Which st atement is true?()

    A. Router RTA is the BDR

    B. Router RTA is directly connected to interface 192.168.45.1

    C. Neighbor 192.168.45.1 has changed its OSPF priority number

    D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs


    参考答案：A

  • 第19题：

    Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B?()

    A.The loopback addresses are on different subnets

    B.The value of the dead timers on the router are different

    C.Route summarization is enabled on both routers

    D.The process indentifier on router A is different than the process identifier on router B


    参考答案：B

  • 第20题：

    Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）

    A.The Manchester serial address is 10.1.1.1

    B.The Manchester serial address is 10.1.1.2

    C.这个Manchester路由器串口地址为：10.1.12

    D.The London router is a Cisco 2610.

    E.The Manchester router is a Cisco 2610.

    F.The CDP information was received on port Serial0/0 of the Manchester router.

    G.The CDP information was sent by port Serial0/0 of the London Router.


    参考答案：A, D, F

  • 第21题：

    You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes. Which two things should you verify to troubleshoot this problem?（）

    • A、The border router is using a proper seed metric for OSPF
    • B、The border ro uter is using a proper seed metric for EIGRP
    • C、The administrative distance is set for OSPF and EIGRP
    • D、The missing EIGRP routes are present in the routing table of the border router
    • E、The subnet keyword on the border router in the redistribute EIG RP command

    正确答案:D,E

  • 第22题：

    单选题
    Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）
    A

    10.1.1.2

    B

    10.154.154.1

    C

    172.16.5.1

    D

    192.168.5.3


    正确答案： B
    解析： 暂无解析

  • 第23题：

    单选题
    Refer to the exhibit. With an IPSec tunnel established between remote Router A and head-end router B, with Compressed Real-Time Protocol (cRTP) configured on the serial interface of Router A, what impact will the cRTP configuration have on the Voice over IP packets flowing through the IPSec tunnel from a Cisco 7960 IP phone?（）
    A

    Twenty bytes of header will be replaced with five bytes. 

    B

    If the IPSec transform set includes Authentication Header, the receiving IPSec peer will discard the packets. 

    C

    The IPSec packets will be dropped by Router A's compression logic.

    D

    The voice packets will not be compressed.


    正确答案： B
    解析： 暂无解析

相关内容