A. Thin Film filter
B. Fiber Bragg Grating
C. Arrayed Wave Guide
D. Erbium fiber amplifier
第1题:
A. RIP
B. OSPF
C. BGP and RIP
D. RIP and PIM
第2题:
Click the Exhibit button. Given the following parameters: transmitter output (min): -2 dBm receiver input (min): -28 dBm 15216 Mux and Demux loss: 4.5 dB 16 channels maximum In which sites shown in the exhibit could the 15216 EDFAs be placed to minimize the number of EDFAs needed?()
A. Locations B, C only
B. Locations A, B, C only
C. Locations A, B, D only
D. Locations B, C, D only
E. Locations A, B, C, D
第3题:
Click the Exhibit button. Given the information shown in the exhibit, when creating 2 DS1 circuits, how many STS ports are used on the VT1.5 matrix at Node 1 as VT circuits and how many are used after using VT tunnels?()
A.2;0
B.3;2
C.3;5
D.4;0
E.6;0
F.6;2
第4题:
A. revertive
B. circuit type
C. circuit size
D. bidirectional
E. protected drops
F. switch on PDI-P
第5题:
To examine the Exhibit, press the Exhibit button. Which of the following addresses will be reachable without adding any routes?()
第6题:
You have two servers named Server1 and Server2 that run Windows Server 2003 Service Pack 2 (SP2). The IP configuration for Server1 is shown in the Server1 IP exhibit. (Click the Exhibit button.) The IP configuration for Server2 is shown in the Server2 IP exhibit. (Click the Exhibit button.) Server1 is unable to contact Server2. You need to ensure that Server1 can contact Server2. What should you do?()
第7题:
FTP
SSH
Telnet
J-Web
第8题:
Compilation will succeed for all classes and interfaces.
Compilation of class C will fail because of an error in line 2.
Compilation of class C will fail because of an error in line 6.
Compilation of class AImpl will fail because of an error in line 2.
第9题:
over-subscribed
under-subscribed
dedicated circuits
nondedicated circuits
第10题:
0.947 Mbps
3.000 Mbps
4.065 Mbps
282.058 Mbps
第11题:
static source pool
interface source pool
source pool with PAT
souce pool without PAT
第12题:
Three physical interfaces are redundant.
You must define an additional Redundancy Group.
node 0 will immediately become primary in the cluster.
You must issue an operational command and reboot the system for the above configuration to take effect.
第13题:
A. static source pool
B. interface source pool
C. source pool with PAT
D. souce pool without PAT
第14题:
A. fiber failure between Sites A and d
B. EDFA failure at Site A (clockwise direction)
C. EDFA failure at Site C (clockwise direction)
D. 15216 multiplexer at Site A (counter-clockwise direction)
E. OADM pass-through (West "OUT") failure at site D (clockwise)
F. wavelengths 1 and 3 transmitter failures at Site A (clockwise direction)
第15题:
A.1+0
B.1+1
C.1:1
D.1:N
第16题:
To examine the Exhibit, press the Exhibit button. Which of the following addresses should be reachable without adding any routes?()
第17题:
Your network contains a DNS server named Server1 that runs Windows Server 2008 R2.Root hints for Server1 are configured as shown in the exhibit. (Click the Exhibit button.)You need to add root hints to Server1.What should you do first?()
第18题:
Increase the number of nfsd's on the client.
Increase the number of biod's on the client.
Decrease the number of nfsd's on the server.
Increase the size of nfs_socketsize on the server.
第19题:
DNS traffic is denied.
Telnet traffic is denied.
SMTP traffic is denied.
Ping traffic is permitted.
第20题:
This is a uniprocessor system
The "prog" process has a nice value of 107
There are two active processors on this system
The "prog" process will only be scheduled to run on processor 0
第21题:
A RADIUS request is being received from a device that is not configured on the RADIUS Client page.
A user entered an incorrect password during RADIUS authentication.
A RADIUS proxy attempt failed to reach the configured proxy server.
The RADIUS shared secret is incorrect.
第22题:
300-300-100-100-100
300-300-300-100-100
300-300-300-300-100
300-100-100-100-100
第23题:
129.35.57.22
129.35.54.22
129.35.58.22
129.35.254.22