You are troubleshooting an issue which is causing full-sized packets entering the MPLS cloud be dropped. You have discovered that one of the switches in the MPLS core is not a Cisco switch, but otherwise the MPLS MTU size is set to 1508 bytes on the routers.Based on this information, which of these may be the reason the packets are being dropped?()
A. The switch on you MPLS core that was not produced by Cisco does not support oversized packets
B. No switches support oversized packets
C. By definition, the maximum MTU is 1500 bytes
D. As MPLS VPN labeling increases the size of the packet by 8 bytes, the IP MTU should have been changed to 1508
第1题:
A. to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 2 link
B. to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 3 link
C. to two core switches from redundant distribution switches connected with a Layer 2 link
D. to two core switches from redundant distribution switches connected with a Layer 3 link
E. to two core switches running Cisco NSF and SSO from two redundant distribution switches running Cisco NSF and SSO
第2题:
To which switch or switches should you provide redundant links in order to achieve high availability with reliable fast convergence in the enterprise campus?()
第3题:
You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?()
第4题:
Which statement about implementing the Cisco IPv6 provider Edge Router over MPLS is true?()
第5题:
While you are troubleshooting network performance issues, you notice that a switch is periodically flooding all unicast traffic. Further investigation reveals that periodically the switch is also having spikes in CPU utilization, causing the MAC address table to be flushed and relearned. What is the most likely cause of this issue?()
第6题:
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phone to drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserved for roaming on the WLAN controller to themaximum. What level do you set the bandwidth to?()
第7题:
Unknown destination MAC address
Bad cabling
MAC forwarding table is full
Port configured for half duplex
Port configured for full duplex
Network congestion
第8题:
You must set each end of the trunk line to IEEE 802.1e encapsulation.
You must set the same VTP management domain name on both switches.
You must set all ports on the two switches as access ports.
You must configure one of the switches as a VTP server.
You must use a rollover cable to connect the two switches.
第9题:
RSTP
root guard
BPDU guard
GLBP
第10题:
Start LDP.
Enable CEF switching.
Configure conditional label advertising.
Enable label switching on frame mode interfaces.
disable IP TTL propagation
configure conditional label advertising
第11题:
to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 2 link
to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 3 link
to two core switches from redundant distribution switches connected with Layer 2 link
to two core switches from redundant distribution switches connected with Layer 3 link
to two core switches running Cisco NSF and SSO from two redundant distribution switches running Cisco NSF and SSO
第12题:
5 percent
15 percent
25 percent
35 percent
第13题:
You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be a roaming bandwidth issuE. in order to verify what kind of issue it is, you decide to increase the bandwidth reserved for roaming on the wlan controller to the maximum. What level do you set the bandwidth to?()
第14题:
Which Cisco Small Business Switch would you recommend to a small business customer who wants to segment the network into workgroups and have a limited number of voice devices on the network?()
第15题:
You are troubleshooting an issue which is causing full-sized packets entering the MPLS cloud be dropped. You have discovered that one of the switches in the MPLS core is not a Cisco switch, but otherwise the MPLS MTU size is set to 1508 bytes on the routers. Based on this information, which of these may be the reason the packets are being dropped?()
第16题:
Cisco IOS is the software used on the vast majority of Cisco Systems routers and current Cisco network switches. As a network administrator, you are required to configure MPLS on Cisco IOS. In such a situation, which three of the following steps are necessary to take?()
第17题:
You are charged with implementing a secure wireless installation which will provide Internet access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side. Which of the following actionsshould you perform on the wired infrastructure?()
第18题:
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?()
第19题:
The switch on you MPLS core that was not produced by Cisco does not support oversized packets
No switches support oversized packets
By definition, the maximum MTU is 1500 bytes
As MPLS VPN labeling increases the size of the packet by 8 bytes, the IP MTU should have been changed to 1508
第20题:
A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.
All Catalyst switches support ISL trunking.
A Catalyst switch will report giants if one side is configured for ISL while the other side is not.
ISL trunking requires that native VLANs match.
None of the other alternatives apply
第21题:
Setup an ACL that allows and logs all IP traffic between the two computers
Configure a spanning tree to check for a loop
Setup a span port on the switch to watch for CRC errors
Connect both computers using a crossover cable
第22题:
5 percent
15 percent
25 percent
35 percent
第23题:
a routing protocol that is flooding updates
a flapping port that is generating BPDUs with the TCN bit set
STP is not running on the switch
a user that is downloading the output of the show-tech command
a corrupted switch CAM table
第24题:
25 percent
15 percent
5 percent
35 percent