Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?（）A. 10.0.0

题目

Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?（）

A. 10.0.0.0/8

B. 172.16.10.0/24

C. 172.16.0.0/24

D. 10.10.10.0/24

E. 172.16.0.0/16

F. 10.10.0.0/16

相似考题

1.Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B

2.Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

3.Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）A. the routes originating from the RIP routing domainB. the routes originating from the OSPF stub areaC. all OSPF inter and intra - area routesD. all routes originating from RIP and OSPF routing domains

4.Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? ()A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .

更多“Refer to the exhibit. EIGRP is configured with the default configuration on all routers. A ”相关问题

  • 第1题：

    Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

    A. The no auto - summary command needs to be added under router eigrp 1

    B. The subnets keyword was not included in the redistribute command under router ospf 1

    C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

    D. The default - information originate command needs to be added under router ospf 1

    E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF


    参考答案：B

  • 第2题：

    Refer to the exhibit. A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up. W hat did the TAC engineer configure incorrectly?()

    A. The crypto isakmp configuration is not correct.

    B. The crypto map configuration is not correct.

    C. The interface tunnel configuration is not correct.

    D. The network configuration is not correct; netw ork 172.16.1.0 is missing.


    参考答案：A

  • 第3题：

    Refer to the exhibit. A partial routing configuration is shown. Complete the configuration so that only the default - network is redistributed from EIGRP 190 into EIGRP 212. Which ACL statement completes the configuration correctly? （）

    A. access - list 100 permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0 .0

    B. access - list 100 permit ip host 0.0.0.0 any

    C. access - list 100 permit ip any host 0.0.0.0

    D. A default -network cannot be redistributed between routing processes.


    参考答案：C

  • 第4题：

    Refer to the exhibit. You want to use all the routes in the EIGRP topology for IP load balancing. Which two EIGRP subcommands wou ld you use to accomplish this goal?()

    A. traffic - share balanced

    B. distance

    C. maximum- paths

    D. default - network

    E. variance


    参考答案：C, E

  • 第5题：

    Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the routes redistributed from OSPF?()

    A. Redistribution must be enabled mutually (in both directions) to work correctly.

    B. auto - summary causes the OSPF routes redistributed into EIGRP to be summarized; thus the OSPF network 116.16.34 is summarized to 116.3 4.0.0, which is already covered by the EIGRP protocol.

    C. Default metrics are not configured under EIGRP.

    D. Both routing protocols must have unique autonomous system numbers for redistribution to function correctly.


    参考答案：C

  • 第6题：

    Refer to the exhibit. The Route.com company is running EIGRP between all the r outers. Currently, if one of the LAN links (LAN1 or LAN2) at the headquarters flaps (goes up and down), the HQRTR1 and HQ - RTR2 routers will experience high CPU usage and have a long EIGRP convergence time. As the new network administrator, you are asked to investigate this situation and determine if there is a quick way to resolve this issue. Which is the most important thing that you can quickly verify first to resolve this issue?（）

    A. Verify that the bandwidth setting on all WAN links is correct.

    B. Verify that the HQ - RTR1 and HQ - RTR2 routers are configured to send only a default route to all the spoke routers.

    C. Verify that the HQ - RTR1 and HQ - RTR2 routers are configured for EIGRP Nonstop Forwarding.

    D. Verify that all the spoke routers are co nfigured for autosummarization.

    E. Verify that all the spoke routers are configured as EIGRP stub.


    参考答案：E

  • 第7题：

    Which three statements are true about EIGRP route summarization?()

    A.When manual summarization is configured, the router immediately creates a route that points to null0 interface

    B.Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routing

    C.Manual route summarization is configured on the interface

    D.The ip summary - address eigrp command generates a default route with an administrative distance of 5

    E.When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routes

    F.The ip summary - address eigrp command generates a default route with an administrative distance of 90


    参考答案：A, C, D

  • 第8题：

    Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?()

    A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

    B. R4(config)# ip default - network 10.0.0.0

    C. R4(config - router)# default -information originate

    D. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1


    参考答案：B

  • 第9题：

    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

    • A、As numbers must be changed to match on all the routers.
    • B、Loopback interface must be configured so a DR is elected.
    • C、The no auto-summary command is needed on Router A and Router C.
    • D、Router B needs to have two network statements, one for each connected network.

    正确答案:A

  • 第10题：

    Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? （）

    • A、All ports will be in a state of discarding, learning, or forwarding.
    • B、Thirty VLANs have been configured on this switch.
    • C、The bridge priority is lower than the default value for spanning tree.
    • D、All interfaces that are shown are on shared media.
    • E、All designated ports are in a forwarding state.
    • F、The switch must be the root bridge for all VLANs on this switch.

    正确答案:A,C,E

  • 第11题：

    Cat6500（config）# router ospf 1  Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0  Cat6500（config-router）# nsf Cat6500（config-router）#end  Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series  Switch with redundant supervisor engines.  The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational.  What is the most likely reason？ （）

    • A、CEF was not properly configured.
    • B、OSPF was not properly configured for graceful restart.
    • C、Stateful switchover was not correctly configured.
    • D、NSF for OSPF is only supported in area 0.

    正确答案:C

  • 第12题：

    单选题
    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）
    A

    As numbers must be changed to match on all the routers.

    B

    Loopback interface must be configured so a DR is elected.

    C

    The no auto-summary command is needed on Router A and Router C.

    D

    Router B needs to have two network statements, one for each connected network.


    正确答案： B
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Which statement about dynamic routing protocols for this network is true? ()

    A.No dynamic interior routing protocol can summarize as shown

    B.Unless configured otherwise, EIGRP would automatically summa rize the prefixes as shown in the exhibit

    C.With this IP addressing scheme, EIGRP can be manually configured to summarize prefixes at the specified summarization points

    D.The IP address design lends itself to OSPF Each summarizing router would be an ABR, summarizing to the next area in the address hierarchy


    参考答案：C

  • 第14题：

    Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?()

    A. router rip

    B. router eigrp 10

    C. redistribute eigrp 10

    D. redistribute rip

    E. default - metric 10000 100 255 1 1500

    F. default - metric 5


    参考答案：A, C, F

  • 第15题：

    Refer to the exhibit. R1 accesses the Internet using E0/0. You have been asked to co nfigure R1 so that a default route is generated to its downstream devices (191.0.0.1 and 192.0.0.1). Which commands would create this configuration? （）

    A.router eigrp 190redistribute static ! ip route 0.0.0.0 0.0.0.0 Null0

    B.ip default - network 2 0.0.0.0

    C.router eigrp 190 redistribute static ! ip route 0.0.0.0 255.255.255.255 Null0

    D.ip default - network 20.20.20.0


    参考答案：A

  • 第16题：

    Refer to the exhibit. A company would prefer all Internet - bound OSPF routed traffic to use ISP ABC with ISP DEF as a backup. As the network consultant, what three configuration changes might you make?（）

    A. The default -information originate command should be configured on router B1 and B4.

    B. The default -information originate command should be configured on router B2 and B3.

    C. If the metric value for ISP ABC is set at the default, the I SP DEF metric value should be set to 1.

    D. If the metric value for ISP ABC is set at the default, the ISP DEF metric value should be set to 25.

    E. The metric type value should be set to type 1.

    F. The metric type value should be set to type 2.


    参考答案：B, D, F

  • 第17题：

    Refer to the exhibit. ROUTE.com has just implemented this EIGRP network. A network administrator came to you for advice while trying to implement load balancing across part of their EIGRP network. If the variance value is configured as 2 on all routers and all o ther metric and K values are configured to their default values, traffic from the Internet to the data center will be load balanced across how many paths? （）

    A. 1

    B. 2

    C. 3

    D. 4

    E. 5


    参考答案：C

  • 第18题：

    Refer to the exhibit. Which two statements are true about the partial configuration that is provided.()

    A. The peer group shortens the EBGP configuration

    B. The peer group shortens the IBGP configuration

    C. All the configured neighbors are in autonomous system 100

    D. Three AS - path filters are applied to each BGP neighbor

    E. Only the outgoing filters are applied to BGP updates


    参考答案：B, C

  • 第19题：

    Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?()

    A. The no auto - summary command has not been issued under the EIGRP process on both routers.

    B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

    C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.

    D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.


    参考答案：D

  • 第20题：

    Refer to the exhibit. Which value will be configured for Default Gateway of the Local Area Connection?()

    A.10.0.0.0

    B.10.0.0.254

    C.192.223.129.0

    D.192.223.129.254


    参考答案：B

  • 第21题：

    You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）

    • A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.
    • B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.
    • C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.
    • D、There is no network statement configuration in EIGRP for IPv6.
    • E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.
    • F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive

    正确答案:A,D,E

  • 第22题：

    Which three statements are true about EIGRP route summarization?（）

    • A、When manual summarization is configured, the router immediately creates a route that points to null0 interface
    • B、Manual route summarization  is configured in router configuration mode when the router is configured for EIGRP routing
    • C、Manual route summarization is configured on the interface
    • D、The ip summary - address eigrp command generates a default route with an administrative distance  of 5
    • E、When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routes
    • F、The ip summary - address eigrp command generates a default route with an administrative distance of 90

    正确答案:A,C,D

  • 第23题：

    单选题
    Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors？（）
    A

    R4（config）# ip default-network 10.0.0.0

    B

    R4（config）# ip route 0.0.0.0 0.0.0.0 10.1.1.1

    C

    R4（config）# ip route 10.0.0.0 255.0.0.0 10.1.1.1

    D

    R4（config-router）# default-information originate


    正确答案： B
    解析： 暂无解析

相关内容